Chatham BM by Discount Builders Merchants, Northfleet

Boarding a Luton loft floor from joists up

A loft becomes a room by laying a floor across the ceiling joists, then building the walls that stand on it. Most Luton lofts sit under a pitched roof, so the floor and its boards come first and the knee walls follow. This guide takes a floor 3.9 metres wide and 3.0 metres deep and counts every part of it from those two measurements.

Chatham BM is the Chatham and Luton delivery site of Discount Builders Merchants (KENT) LTD, the builders' merchant at Lower Road, Northfleet, DA11 9BB. There is one yard, and orders are placed on www.discountbm.co.uk.

Stacks of treated timber with stickers in the yard

Picking the joist depth first

Start with the clear span, the gap a joist has to bridge between its two bearings, and then with the use the floor will take. A designer or the building control officer turns those into a depth, and that depth is the first line of the order. A sawn treated length runs up to 6 m, so a 4.0 m joist can come from a standard length without a splice.

Before ordering, look at the joists that are already there. Ceiling joists seldom have to carry people, so inspect them: check the bearing ends for rot, and where the design calls for it, add a new joist beside each old one. Shims at the bearing take up any gap so the load lands squarely.

Setting out and counting the joists

Joists sit at a single spacing, usually 400 mm or 600 mm. Divide the length they are spaced along by the spacing, round the answer up, and add one for the joist at the start. On a 3.0 metre run at 400 mm that gives eight spaces and so nine joists. Rafters for a dormer follow the same rule along the roof slope, with a plate at each end.

Make a list of every piece with its length before ordering, so the yard can cut to length in advance and nothing has to be trimmed on the drive. Cutting a 4.8 m length down to a 4.0 m joist leaves an 800 mm offcut, which is worth keeping for blocking between the joists.

Boards for the new floor

The flooring comes as 2400 by 600 mm sheets with tongue-and-groove edges, and one sheet covers 1.44 square metres. Which thickness to lay depends on how far apart the joists are, and the yard's listing gives the thickness in each product name. Check the spacing against the design before the sheets are chosen.

Fasten each sheet with glue and screws at every joist it lies across, and stagger the end joints so none lines up across the floor. A floor laid this way feels solid underfoot and stays quiet when someone crosses it.

Knee walls under the rafters

Under a pitched roof the side walls are short at the eaves and rise towards the middle of the room, so the knee walls are only as tall as the slope allows. A partition across the room runs the full height instead. Both are framed in CLS, which is untreated timber, so keep it indoors and out of any damp.

Lay each wall out at the spacing the boards need. Tie the top plate into the joists above and fix the sole plate to the floor below. Measure the rafter line at several points first, since the slope, not the drawing, decides how long each stud has to be.

Getting long lengths up the house

Long timber is the hard part of a Luton loft. A 4 m length has to round the bend at the top of the stairs or come in through a window, and either route needs checking before the lengths are fixed. Measure the bend at the foot of the stairs and again on the landing, and note the width of the window if that is the way in.

Plan the drop for the day the roof goes on, because timber left open to the rain swells and warps. Stack the sheets flat on bearers, clear of the ground and under cover until they are fixed. Any splice or changed member needs the designer's approval first.

Rules of thumb

Working figures for planning an order. Check them against your drawings and the product you choose.
Joists The run's length divided by the spacing, rounded down, plus one. The depth and spacing come from the design or a span table.
Flooring chipboard A sheet of 2400 by 600 mm gives 1.44 square metres of cover. Add about a tenth for the edges that are cut off.
OSB deck Full 18 mm sheets come to about 2.98 square metres each. Use them for a roof slope or a dormer cheek, and leave the floor to the chipboard.
Knee-wall studs One stud at each step of the board spacing, plus one, all cut to the height under the slope.
Joist lengths Pick the standard length that wastes least, and keep every offcut over 300 mm for blocking.
Stair turn Measure the bend at the foot and the landing before any length is chosen.

The shop has calculators that turn a measurement into a quantity.

Worked order: A 3.9 metre loft floor in Luton

Priced with the shop's prices today, last checked , and the yard's delivery charge to ME4. Amounts are ex VAT unless marked.
Product Quantity What it is for Cost
200x47x4800mm Sawn Treated Timber (8"x2") 9 at £19.17 Clear span 3.9 m, floor 3.0 m deep. Eight spaces at 400 mm across that 3.0 m gives nine joists. Each is cut to 4.0 m from a 4.8 m length: the 3.9 m clear plus 50 mm at each bearing. Check the depth against a span table for 3.9 m before ordering. £172.53
T&G Chipboard Flooring 2400x600x18mm 9 at £10.99 The floor is 11.7 square metres. A tenth more for cuts is 12.9, and at 1.44 square metres a sheet that is 8.9, so nine. £98.91
63x38x2400mm (3" x 2") CLS Timber 5 at £3.59 Knee wall of 2.0 m at 400 mm centres: five spaces give six studs. Each stud is 1.2 m, so two fit a 2.4 m length and three lengths cover them. The plates are 2.0 m, one 2.4 m length apiece. Five in all. £17.95
Goods £289.39
Delivery to ME4 £0.00
Delivered total ex VAT £289.39
Delivered total inc VAT £347.27

Not in this order: Hangers, nails and fixings, the roof ridge and rafters, the insulation and any steel the design calls for. None of those is in the lines above.

The quantities are a starting point for a job of this size. Put the same goods in a basket on www.discountbm.co.uk with your own postcode to see the figure for your order, or send the yard your list.

On the shop today

The products this guide talks about, from the shop's Timber & Sheet Material aisle. Prices last checked .

Prices are the shop's prices today. Stock and ordering are on www.discountbm.co.uk.

Timber and sheet for Chatham, Luton and the Dockyard See all Timber & Sheet Material on the shop

Delivery to Chatham and Luton

ME4

Free when the goods reach £41.66 ex VAT (£49.99 inc VAT).

A smaller order pays the difference up to that amount: goods of £25.00 ex VAT (£30.00 inc VAT) pay £16.66 ex VAT (£19.99 inc VAT) for delivery.

Delivery charges by district · Contact the yard

More guides for Chatham and Luton